Making a Carving Station with Patrick Hoggard

PDF logoIf you would like your own hardcopy of this description, click here

Materials List, Unit of Measure = Inches

  • 1 – 2" x 2" x 5" Blank, Threaded Ball Hitch
  • 1 – 3" x 3" x 3" Blank, Ball Hitch Base
  • 1 – 4" x 12" x ¾" Base
  • 2 – 2" x 6" x ¾", Uprights
  • 1 – ½" x 1 ½" x 4" Blank
  • 1 – 7/8" x 2" x ¾"
  • 5/16" x 4" Carriage Bolt, Washer and Nut
  • ¼ x 4 ½" Carriage Bolt, Washer and Nut
  • 5 – 1 ½" Pocket Hole Screws

Mount the 2" x 2" blank in the chuck and turn a tenon 1 inch long by 1 ¼ inch diameter and thread the tenon with a [Beal] 1 ¼ x 8 TPI die.

Turn a tenonThread a tenon

Mount a 1 7/8" x 2" x ¾" block of wood, turn top profile, and drill a 1 ⅛" hole; then thread with a [Beal] 1 ¼ x 8 TPI tap.

Turn the profileThread the profile

Screw the blank into the block and turn a sphere on the end.

Screw the blank into the blockTurn a sphere

For the 2" x 6" x ¾" uprights, measure from the top 1 inch down. Remove 2 jaws from the chuck and mount the upright and turn a shallow cove. Repeat
for the second one.

Create uprightsCreate uprightsRound the top of uprightsDrill hole in uprights

Turn the cove to match the sphere. Measure down from the top 2 ½ inches from the top and drill a 5/16 inch hole in both uprights for the clamping bolt. Round the top of the uprights.

Mount the dowel

Mount the 1 ½" x 1 ½" x 4" blank and turn a 1 inch dowel 3 ½ inches long. Mount the 1 7/8 x 2" x ¾" blank in the chuck and drill a 1 inch hole ¼ inch deep in the center. Drill 3/16 inch hole all the way through.

Draw the linesFor the 4" x 12" x ¾" base, measure 1 inch in from the end, drill a 1 inch hole in the center. Measure 3 ½ inches from the same end and draw line across. Measure ¾ inch on each side of line you just drew and draw a line across each one. Mark out 4 equal segments between the two outer lines. Take the base to the band saw a cut down the center line.


Cut out every other segment

Cut out every other segment on the long piece; cut the opposite two segments on the short piece. Sand or trim to get a snug fit.

Fit 2 pieces togetherFit the 2 pieces together and mark the center of the hinge and drill a ¼ inch hole all the way through.

Drill and tap a hole

Round over the ends of the hinge so it swivels up and down.

Drill and tap a hole for a ¼ x 20 TPI screw in the end of the base where the 1 inch hole is to lock the dowel. Turn a small knob for the ¼-20 screw and epoxy it on.

Round over the ends of the hinge

All that is left is assembly. Glue and screw the dowel into the hole on the 1 7/8" x 2" x ¾" stand base. Insert the sphere in the coves of the uprights and insert the 5/16" x 4" carriage bolt through both uprights and install washer and nut, place the 1 7/8" x 2" x ¾" piece at the bottom of theFinished carving stand

uprights and glue and screw together. Insert ¼" x 4 ½" inch bolt through the hinge and install washer and nut.

A demo on how to do this was done on November 18, 2026, and is available belows!

Enjoy!

Leave a Reply

Your email address will not be published. Required fields are marked *